Particle board becomes more useful after having a coat of sealant. The coating can be enjoyable if you know the right way of how to seal the particle board. Don’t worry about how to stain the particle board. Just read the easy steps below to enhance the durability of the particle board. Get the easy solutions of how do you fix a damaged particle boardat the last of the article.
How to seal particle board
Step 1 Arrange the things below: At first, get the things below for that sake of doing the operation easily.
- Goggles
- Mask
- Saw or jigsaw
- Painting brush
- Paint rollers
- Sealant
- Dump cloths
- Measurement tap
- Marker
Step 2 Take security measures
Before starting, put on security measures such as goggles, masks, and hand gloves. You know particle boards come from the sawdust, wood chips, and glues. When cutting the board, it may kick back splinters in the air. You won’t want that sawdust disturbing your eyes in the project.
Step 3 Measure the particle board
Get the measurement tape and a marker to select the area. Measure the targeted area at first where you want to install the particle board. Get the total measurement in height and width. Place the tap on the board and match the total measurement that you got from the area. Mark the ground of the board that you need to cut.
Listen: Sealing the entire particle board may cost you more.
Step 4 Cut the board as you need
Take the jigsaw and start cutting from one side following the marked line. Don’t be so hurry while cutting the board lest you may ruin the whole project.
Step 5 Apply the sealant in the entire area
Put off the cap of the acrylic sealant. Jerk the sealant before applying. Take the paintbrush in one hand and the sealant pack on the other hand. Press the pack and scrape the sealant with the brush smoothly. Paint the entire part of the board following the same process. Add more sealant to the areas that are more prone to damage. Make sure you have done both sides of the board.
Step 6: Let it dry
Hold the board with two tiny objects and place it to the open air. Let it dry for sometimes. In the case of a hurry, you can use the hairdryer to dry up the board. Keep in mind that it should not warm the board instead of drying up.
Step 7 Check out and follow up
When it is dry enough, check out the particle board attentively whether you missed any portion or not. Install the board on the targeted place.
Read more nail gun
When to apply a sealant on the board
- When you think the board is prone to wet in the rain
- If there is a chance to get overheat
- If the board needs to carry weight
- If you are going to place a new board in a potential area
- To enhance the internal decoration of your room
- When it is getting damaged
- To reuse the particle board
What is a particle board sealer used for?
To make the board durable
A sealant can enhance the durability of the particle board undoubtedly. This sealant covers the board with a hard substance that can take extreme heat, rain, snow, and little weight.
You may not use particle board naked in your kitchen, window, or the rooftop without the sealant. To have a permanent solution, you cannot but use a sealant on the board.
To save the board from water, and sun
The hard substance of the sealant can tolerate the dirty whether no matter snowing, raining, or heat. The sealant penetrates the particle board from the deeper to be harder and protectable.
To strengthen the board
Nobody goes to use particle board directly in a hard place that can damage the board. Applying a sealant on the same board makes you confident to install the boar anywhere you want.
To enhance the usability
After having a coat of sealant, ordinary particle board becomes a harder object. You know the ease of installation of the board anywhere. The usability of the sealant particle board enables you to place the board anywhere blindly.
Can wet particle board be repaired?
In short, the answer is “Yes”. Obviously, you can repair wet particle board if you know the right way of how to repair wet particle board.
You can repair the board easily by applying a sealant in the entire board following the methods below. Here, you have to check out the density of the board whether it is repairable or not.
How do you fix a damaged particle board?
- Dry up the wet or damaged area of the board in the air. You can use a hairdryer to make it quick. Make it’s not too warm.
- Add some sand or sandpaper into the damaged or wet area. Use your naked hand to do so.
- Clean up the area with the hair drier. Make sure, you have the goggles in your eyes. It blows the sawdust in the air.
- Apply the sealant in the area of the damage following the first paragraph.
- Don’t be hurry lest you may lose it again.
Bottom line
Already you have the instructions on how to seal particle board with other essential solutions. Before starting the operation in your project, take necessary security measures. A small coat of sealant can enhance the durability of your particle board.
